Skip to contentPractice exam

# Truck and Coach Technician (310T) Practice Exam

Practise for the Ontario 310T exam with 30 free questions from Ontario Certification Registry, a score and explanations. The full 150-question PDF includes these 30 plus 120 more, with an answer key and references.

Try 30 questions freeFull 150-question PDF · $67.49 CAD

- Secure checkout by Stripe
- PDF emailed in minutes
- Yours to keep

Updated 2026-11-11.

![Truck and Coach Technician (310T) Practice Exam cover](https://tradecredentialregistry.com/exam-covers/310t-truck-and-coach-technician-768.png)

Free practice test

## Try 30 questions free

Work through 30 questions, then see your score, results by topic and an explanation for every answer. No account or email needed.

These are 30 of the 150 questions in the full PDF. You can also read the questions and answers below.

## The full 150-question PDF

Includes the 30 free questions plus 120 additional questions, explanations and references. One payment, no subscription.

| Questions | 150, all original |
| --- | --- |
| Answer key | Correct answer, the reasoning, and a cited source for each question |
| Distinct references | 79 distinct citations across the bank |
| Free samples here | 30, with answers, below |
| Format | PDF, emailed on purchase, plus a download link valid 30 days |
| Price | $67.49 CAD, one payment, no subscription |

Payment is handled by Stripe. This is study material, not an official exam, and it is not affiliated with Skilled Trades Ontario, TSSA or the Red Seal program.

## Look inside the PDF

A preview of the question and answer-key layout, using questions from the free sample. The full guide contains all 150 questions.

![Preview of the printable question page, using free sample questions](https://tradecredentialregistry.com/exam-previews/310t-truck-and-coach-technician-questions.png)![Preview of the answer key with explanations and source references](https://tradecredentialregistry.com/exam-previews/310t-truck-and-coach-technician-answers.png)

## What this guide covers

The still-published Red Seal exam-information page lists a 135-question Truck and Transport Mechanic exam and blocks A-K. Its counts are scaled to 150 with largest-remainder rounding. The Red Seal overview says exams based on the newer RSOS are under development, so established-system questions cite the Ontario 310T Apprenticeship Training Standard (2016); only four hybrid/EV questions use the newer RSOS. This is an independent study allocation, not an official examination. The table shows the actual counts and shares in this guide.

| Major work activity | Questions here | Share of this guide |
| --- | --- | --- |
| A. Common occupational skills | 9 | 6% |
| B. Engines and supporting systems | 23 | 15.3% |
| C. Air systems and brake systems | 19 | 12.7% |
| D. Electrical and electronic systems | 24 | 16% |
| E. Drive trains | 19 | 12.7% |
| F. Steering, chassis, suspensions, tires, wheels and hubs | 20 | 13.3% |
| G. Cabs | 6 | 4% |
| H. Trailers | 9 | 6% |
| I. Climate control systems | 8 | 5.3% |
| J. Hydraulic systems | 9 | 6% |
| K. Hybrid and electric vehicles | 4 | 2.7% |

The published official exam has 135 questions. This guide contains 150 original study questions, with topic counts rounded to fit that length.

Coverage source: [Published Red Seal exam breakdown](https://red-seal.ca/eng/trades/trucktranspmech/exam-information.shtml)

## The mix of question types

The table compares this guide's mix with the published Red Seal ranges for this trade.

| Type | Questions here | Share | Published range |
| --- | --- | --- | --- |
| Knowledge and recall | 14 | 9.3% | 0 to 9.999% |
| Procedural and application | 83 | 55.3% | 50 to 60% |
| Critical thinking | 53 | 35.3% | 35 to 45% |

## 30 free sample questions from the Truck and Coach Technician bank

This fixed selection comes straight from the bank and covers every major work activity, with the answers and sources shown. Read them before you decide whether the rest is worth $67.49 to you.

### Question 1: A bulletin applies to some model years only. The truck's VIN is 3HSDZAPR0RJ482716. Which model year does the VIN identify?

### Sample 1 · Activity A

**A bulletin applies to some model years only. The truck's VIN is 3HSDZAPR0RJ482716. Which model year does the VIN identify?**

1. 2025
2. 2023
3. 2018
4. 2024 (correct)

The model year is the 10th VIN character, here R, and the year codes skip I, O, Q, U, Z and 0, so P = 2023, R = 2024 and S = 2025. Reading J, the 11th character (plant code), gives 2018, and miscounting to the P in position 7 gives 2023. Model year is not the build date, so a bulletin keyed to a build date or serial range still needs the full VIN checked in the maker's system.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5135.05. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf Also: 49 CFR 565.15(d) and Table VII, VIN model year codes. https://www.law.cornell.edu/cfr/text/49/565.15

### Question 2: Which section of a WHMIS safety data sheet sets out the personal protective equipment to use with a product?

### Sample 2 · Activity A

**Which section of a WHMIS safety data sheet sets out the personal protective equipment to use with a product?**

1. Section 8, exposure controls (correct)
2. Section 7, handling and storage
3. Section 11, toxicological info
4. Section 4, first-aid measures

Under the Hazardous Products Regulations an SDS has 16 sections, and section 8 (exposure controls/personal protection) gives exposure limits, engineering controls and individual protection measures such as PPE. Section 7 covers safe handling and storage conditions, which makes it the tempting choice, while section 4 covers first aid and section 11 health effects. How the information is applied still depends on the workplace controls and WHMIS training.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5135.07. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf Also: CCOHS, Safety Data Sheet (SDS) fact sheet, table of the 16 SDS sections (revised 2026-05-28). https://www.ccohs.ca/oshanswers/chemicals/whmis_ghs/sds.html

### Question 3: A low oil pressure lamp comes on at hot idle. The oil level and condition are correct, and the dash gauge shows 40 kPa. What is the first test?

### Sample 3 · Activity B

**A low oil pressure lamp comes on at hot idle. The oil level and condition are correct, and the dash gauge shows 40 kPa. What is the first test?**

1. Refill with a heavier grade oil
2. Remove the pan to check pickup
3. Replace the oil pressure sender
4. Master gauge at the sender port (correct)

The lamp and dash gauge both rely on the sender and its circuit, so a mechanical master gauge at the sender port shows whether pressure is really low before anything is replaced or removed. If the master gauge reads normal, test the sender and circuit; if it reads low, compare it with the maker's hot-idle specification and continue with internal checks. A heavier oil can mask a real lubrication fault.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5139.05. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 4: A truck has a spring-engaged, air-released fan clutch. Coolant reaches 104 °C at idle but is normal at road speed. The ECM commands the fan on, the clutch air port reads 0 kPa, and the fan turns 450 rpm while its drive pulley turns 1,700 rpm. What is the fault?

### Sample 4 · Activity B

**A truck has a spring-engaged, air-released fan clutch. Coolant reaches 104 °C at idle but is normal at road speed. The ECM commands the fan on, the clutch air port reads 0 kPa, and the fan turns 450 rpm while its drive pulley turns 1,700 rpm. What is the fault?**

1. Fan clutch is slipping (correct)
2. Solenoid not venting air
3. Clutch air supply too low
4. Thermostat stuck closed

On this design, venting the air lets the spring lock the fan to the pulley, and 0 kPa at the port shows the ECM command and solenoid did their job. A fan turning 450 ÷ 1,700 = 26% of pulley speed is slipping, which points to worn friction material or a weak engagement spring. A solenoid stuck applying air would leave pressure at the port, and a closed thermostat would overheat the engine at road speed too and would not make the fan slip.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5139.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 5: On a cold start, the full-flow oil filter is badly plugged. What keeps oil reaching the bearings?

### Sample 5 · Activity B

**On a cold start, the full-flow oil filter is badly plugged. What keeps oil reaching the bearings?**

1. The filter bypass valve (correct)
2. The anti-drainback valve
3. The pressure relief valve
4. The cooler bypass valve

When the pressure difference across a plugged or cold-thickened element passes its setting, the bypass valve opens and sends unfiltered oil to the galleries, because unfiltered oil is better than none. The relief (regulating) valve limits maximum pump pressure, the anti-drainback valve keeps the filter full at shutdown, and a cooler bypass routes cold oil around the oil cooler. A filter on bypass is not filtering, so service intervals and oil condition still matter.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5139.05. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 6: A cylinder leakage test on cylinder 3 at TDC compression shows 40% leakage. Air is heard at the exhaust outlet, with none at the intake, crankcase breather or coolant tank. What is leaking?

### Sample 6 · Activity B

**A cylinder leakage test on cylinder 3 at TDC compression shows 40% leakage. Air is heard at the exhaust outlet, with none at the intake, crankcase breather or coolant tank. What is leaking?**

1. Piston rings worn
2. Exhaust valve not sealing (correct)
3. Intake valve not sealing
4. Head gasket breached

Air escaping through the exhaust path means the exhaust valve is not seating, for example a burnt or carboned seat, a bent valve or no valve lash. An intake valve leak is heard at the air inlet, ring leakage at the breather or oil filler, and a head-gasket or cracked-head leak bubbles in the coolant. The crank must be held at TDC on compression so both valves are closed, or the reading is meaningless.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5139.08. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 7: After the governor cuts out, how is its cut-in pressure checked with the engine idling?

### Sample 7 · Activity C

**After the governor cuts out, how is its cut-in pressure checked with the engine idling?**

1. Read where the build-up stops
2. Read where the dryer purges
3. Fan brakes; read where it climbs (correct)
4. Drain; read where buzzer stops

Fanning the brake pedal lowers reservoir pressure, and the reading at which the gauge starts climbing again is where the governor loads the compressor, the cut-in pressure. The point where build-up stops and the dryer purges is cut-out, and the buzzer only tests the low-pressure warning switch. Compare both readings with the maker's range, since the difference between them matters too.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5149.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 8: Cut-out is specified at 860 kPa. At 860 kPa, a gauge at the compressor end of the governor signal line shows full pressure, yet the compressor keeps building until the safety valve opens near 1,030 kPa. What is the fault?

### Sample 8 · Activity C

**Cut-out is specified at 860 kPa. At 860 kPa, a gauge at the compressor end of the governor signal line shows full pressure, yet the compressor keeps building until the safety valve opens near 1,030 kPa. What is the fault?**

1. Safety valve set too low
2. Governor signal line kinked
3. Compressor unloader stuck (correct)
4. Governor cut-out set high

The governor sent its signal at the right pressure and it reached the compressor, so the governor and the line are working, and the compressor is not responding to it, which points to a stuck unloader mechanism. A safety valve opening near 1,030 kPa is doing its job because the pressure really is too high. Repair the unloader before release, as repeated over-pressure stresses the dryer and lines.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5149.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 9: On a typical truck air system, which reservoir collects most of the water and oil that get past the compressor and air dryer?

### Sample 9 · Activity C

**On a typical truck air system, which reservoir collects most of the water and oil that get past the compressor and air dryer?**

1. Secondary reservoir
2. Trailer reservoir
3. Primary reservoir
4. Supply reservoir (correct)

Air leaves the dryer into the supply (wet) reservoir first, where it slows and cools, so carry-over water and oil settle there before check valves feed the primary and secondary reservoirs. Draining it as the maker directs shows how well the dryer is working, and large amounts point to a saturated desiccant or a compressor passing oil. The primary and secondary reservoirs should then stay close to dry.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5149.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 10: Steer brakes feel uneven. At 620-690 kPa, pushrod marks move from 38 to 73 mm on the left and from 40 to 89 mm on the right. These are standard-stroke type 24 chambers (limit 44 mm; the long-stroke version is 51 mm). What is found?

### Sample 10 · Activity C

**Steer brakes feel uneven. At 620-690 kPa, pushrod marks move from 38 to 73 mm on the left and from 40 to 89 mm on the right. These are standard-stroke type 24 chambers (limit 44 mm; the long-stroke version is 51 mm). What is found?**

1. Right is beyond the limit (correct)
2. Both are within the limit
3. Left is beyond the limit
4. Both are beyond the limit

Stroke is applied minus released position: left 73 - 38 = 35 mm and right 89 - 40 = 49 mm, so only the right exceeds the 44 mm limit for a standard-stroke type 24. Comparing applied positions with the limit makes both look out, and using the 51 mm long-stroke limit makes both look acceptable, so confirm the chamber type from its tag. An over-stroking brake develops less force, which explains the uneven braking, so find why it is out of adjustment before release.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5150.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 11: A truck cranks slowly. One battery reads 12.2 V open circuit with the surface charge removed, then 9.1 V at the end of a half-CCA, 15 s load test at 21 °C (minimum 9.6 V). What is the next step?

### Sample 11 · Activity D

**A truck cranks slowly. One battery reads 12.2 V open circuit with the surface charge removed, then 9.1 V at the end of a half-CCA, 15 s load test at 21 °C (minimum 9.6 V). What is the next step?**

1. Retest at one-third CCA
2. Repeat the load test now
3. Charge it, then retest (correct)
4. Replace it as failed

12.2 V at rest is roughly a 50% state of charge, and a load test only judges a battery that is at least about 75% charged (about 12.4 V), so this 9.1 V result does not yet prove the battery is bad. Charge it fully and repeat the test, replacing it only if it still falls below 9.6 V. A lower load or an immediate repeat just retests a flat battery, and why it was discharged (parasitic draw or a charging fault) still needs finding.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5136.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 12: A 160 A alternator gives 105 A on a loaded output test at the specified speed. Belt tension and field current are in specification. AC ripple at the output terminal is 1.6 V AC against a 0.5 V AC limit. What is the likely cause?

### Sample 12 · Activity D

**A 160 A alternator gives 105 A on a loaded output test at the specified speed. Belt tension and field current are in specification. AC ripple at the output terminal is 1.6 V AC against a 0.5 V AC limit. What is the likely cause?**

1. Regulator setpoint too low
2. Worn brushes or slip rings
3. Undersized output cable
4. Failed rectifier diode (correct)

An open or shorted rectifier diode removes part of each output cycle, which cuts maximum output noticeably and shows up as high AC ripple. Correct field current rules out worn brushes, slip rings and a regulator under-driving the field, and a cable fault shows as a DC voltage drop, not ripple. A stator phase fault gives the same pattern, so confirm on the bench before choosing the repair.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5136.05. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 13: How is a voltmeter connected to measure the voltage drop along a starter ground cable?

### Sample 13 · Activity D

**How is a voltmeter connected to measure the voltage drop along a starter ground cable?**

1. Across it, with key off
2. In series, with key off
3. Across it, while cranking (correct)
4. In series, while cranking

Voltage drop is measured in parallel across the section being tested while it carries working current, so the meter leads go to the two ends of the cable during cranking. With no current, even a badly corroded cable shows almost 0 V, because the drop equals current times resistance. A voltmeter is never placed in series; that is how an ammeter is connected.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5136.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 14: A truck cranked slowly only after nights at −20 °C. A corroded engine-to-frame ground strap was replaced, and it now cranks well in the warm shop. Which check best verifies the repair?

### Sample 14 · Activity D

**A truck cranked slowly only after nights at −20 °C. A corroded engine-to-frame ground strap was replaced, and it now cranks well in the warm shop. Which check best verifies the repair?**

1. Cranking test in the warm shop
2. Battery open-circuit voltage
3. Ohmmeter check of the strap
4. Cranking test after cold soak (correct)

The fault appeared only after a cold soak, so the repair is proven only when the truck cranks normally under those conditions, ideally with cranking voltage and cable drops recorded. A warm-shop crank could have passed even before the repair, and an ohmmeter cannot resolve the fraction of a milliohm that matters at several hundred amps. Open-circuit voltage shows state of charge, not starting-circuit performance.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5136.04. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 15: During cranking, the battery posts read 10.4 V. The positive cable drops 0.2 V and the ground path 0.2 V; each is allowed 0.5 V. The starter motor (M) terminal to housing reads 8.6 V. Where is the main loss?

### Sample 15 · Activity D

**During cranking, the battery posts read 10.4 V. The positive cable drops 0.2 V and the ground path 0.2 V; each is allowed 0.5 V. The starter motor (M) terminal to housing reads 8.6 V. Where is the main loss?**

1. Battery state of charge
2. Solenoid main contacts (correct)
3. Ground cable path
4. Positive cable path

The starter B terminal should see 10.4 − 0.2 − 0.2 = 10.0 V, but the motor terminal on the far side of the solenoid contacts has only 8.6 V, so 1.4 V is lost across the contacts. Both cable paths are inside their 0.5 V allowance, and 10.4 V at the posts while cranking shows the batteries are holding up. Confirm with a direct B-to-M reading while cranking, then replace the solenoid or its contact set.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5136.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 16: A manually adjusted pull-type clutch slips. Free pedal is about 3 mm (truck spec 38 to 51 mm), and the release-bearing-to-clutch-brake gap is 19 mm (spec 12.7 to 14.2 mm). What is the fix?

### Sample 16 · Activity E

**A manually adjusted pull-type clutch slips. Free pedal is about 3 mm (truck spec 38 to 51 mm), and the release-bearing-to-clutch-brake gap is 19 mm (spec 12.7 to 14.2 mm). What is the fix?**

1. Replace the release bearing
2. Make the internal adjustment (correct)
3. Replace the clutch brake
4. Adjust the external linkage

As the facings wear, the release bearing moves toward the yoke fingers, which uses up free pedal and opens the bearing-to-brake gap until the yoke loads the bearing and the clutch cannot clamp fully. The internal adjustment moves the bearing back to 12.7 to 14.2 mm, and free pedal returns with it. Adjusting the linkage would restore pedal free play but leave the bearing position wrong; if it still slips once both are correct, the clutch is worn out.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5142.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf Also: Eaton, Service Manual: Eaton Heavy-Duty Clutches CLSM0200 (May 2012 copy), Easy Pedal Advantage manual adjust Set-Up and Verify Clutch Brake Squeeze; General Information, When to Inspect the Clutch. https://assets.wellertruck.com/reference-materials/troubleshooting-manuals/eaton-fuller-heavy-duty-clutch-service-manual-rr-clsm-0200.pdf

### Question 17: A 10-speed range transmission with a 1/6, 2/7, 3/8, 4/9, 5/10 lever pattern jumps out of both 3rd and 8th under load. Every other gear holds. Which area is implicated?

### Sample 17 · Activity E

**A 10-speed range transmission with a 1/6, 2/7, 3/8, 4/9, 5/10 lever pattern jumps out of both 3rd and 8th under load. Every other gear holds. Which area is implicated?**

1. Range-shift air system
2. Range-section synchronizer
3. Main-section 3/8 gear position (correct)
4. Driveline working angles

3rd and 8th use the same main-section gear and sliding clutch, with the range section in low for 3rd and high for 8th, so a fault shared by both lies in that main-section position: worn or tapered clutching teeth, the sliding clutch, its shift yoke or the rail detent. A range synchronizer or range air fault would affect gears in one range, not one lever position in both. Driveline angles and vibration can promote jump-out, but would not single out one gear position.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5142.05. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 18: What do the coil springs in a clutch disc hub do?

### Sample 18 · Activity E

**What do the coil springs in a clutch disc hub do?**

1. Absorb torsional vibration (correct)
2. Compensate for facing wear
3. Supply the clamping force
4. Centre the disc on the shaft

The hub (damper) springs let the facings and hub turn slightly relative to each other, soaking up engine firing pulses and torque shocks before they reach the transmission. Clamping force comes from the pressure-plate springs, the splined hub centres the disc on the input shaft, and wear is taken up by internal or self-adjustment in the cover assembly. Broken damper springs can cause gear rattle and driveline noise.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5142.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 19: An automatic transmission flares between shifts and logs ratio codes. At 82 °C sump temperature, idling in neutral on level ground, the fluid reads 40 mm above the HOT FULL mark. What is done first?

### Sample 19 · Activity E

**An automatic transmission flares between shifts and logs ratio codes. At 82 °C sump temperature, idling in neutral on level ground, the fluid reads 40 mm above the HOT FULL mark. What is done first?**

1. Pressure-test the clutches
2. Correct the fluid level (correct)
3. Replace the shift solenoids
4. Reset the shift adaptives

Overfill lets rotating parts churn the fluid into foam, and aerated fluid compresses, so clutch apply pressure becomes low and erratic and shifts flare. Set the level, check the fluid for foam and burnt odour, clear the codes and road test before any pressure testing. Resetting adaptives on aerated fluid would teach the controller false values, and nothing yet points to the solenoids.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5142.08. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 20: Steering effort is high in both directions. Pump flow and relief pressure meet specification. Which step separates a steering-gear fault from linkage or kingpin binding?

### Sample 20 · Activity F

**Steering effort is high in both directions. Pump flow and relief pressure meet specification. Which step separates a steering-gear fault from linkage or kingpin binding?**

1. Disconnect the drag link (correct)
2. Bleed air from the gear
3. Adjust the sector lash
4. Raise the relief setting

With the drag link off the pitman arm, the steering wheel turns the gear alone, and with the axle raised the wheels can be swung by hand to feel linkage and kingpin drag; whichever side stays stiff holds the fault. Adjusting sector lash without a diagnosis can make a gear bind more at centre, bleeding treats noise and erratic assist, and the hydraulic supply has already passed. Dry or seized kingpins are a common heavy-truck cause.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5147.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 21: A steer-tire assembly shakes at 90 km/h despite correct balance. Mounted on the hub, radial runout is 2.8 mm at the tread (limit 2.3 mm) and 0.4 mm at the rim bead seat (limit 1.3 mm). What is the cause?

### Sample 21 · Activity F

**A steer-tire assembly shakes at 90 km/h despite correct balance. Mounted on the hub, radial runout is 2.8 mm at the tread (limit 2.3 mm) and 0.4 mm at the rim bead seat (limit 1.3 mm). What is the cause?**

1. Wheel off-centre on hub
2. Assembly out of balance
3. Tire out of round or unseated (correct)
4. Wheel bent at the rim

Measured on the hub, rim runout captures both a bent wheel and an off-centre mounting, and 0.4 mm is well within its limit, so the excess at the tread comes from the tire: uneven bead seating or a tire that is out of round. Balance is already correct and cannot correct runout. Check the bead seating line, re-seat or match-mount the tire, and replace it if runout stays high.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5148.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 22: What does positive caster mainly give a truck's steer axle?

### Sample 22 · Activity F

**What does positive caster mainly give a truck's steer axle?**

1. Even shoulder wear
2. Lighter steering effort
3. Less scrub in turns
4. Straight-line stability (correct)

Positive caster tilts the top of the kingpin rearward so the tire's contact patch trails the steering axis, which makes the wheels self-centre and run straight. More caster raises steering effort rather than lowering it, shoulder wear is governed mainly by camber and toe, and scrub in turns is reduced by toe-out on turns (Ackermann geometry). Unequal caster side to side can cause a pull.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5147.05. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 23: An air-suspended tractor sits low on both sides of the drive axles. After dumping and refilling the air springs, ride height is 205 mm against a 216 ± 3 mm specification, and the springs hold pressure. What is done?

### Sample 23 · Activity F

**An air-suspended tractor sits low on both sides of the drive axles. After dumping and refilling the air springs, ride height is 205 mm against a 216 ± 3 mm specification, and the springs hold pressure. What is done?**

1. Replace the air springs
2. Fit longer shock absorbers
3. Reset the height-valve linkage (correct)
4. Increase the system air pressure

The height control valve admits or exhausts air until its arm returns to neutral, so a uniformly low ride height with sound air springs is corrected by adjusting the valve linkage, often with a locating pin, then dumping, refilling and remeasuring. System pressure does not set ride height, and shock absorbers carry no load. Correct ride height also restores the driveline angles the maker designed for.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5146.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 24: After a door glass replacement, the power window slows and stalls mid-travel. With the glass unbolted, the regulator runs full travel drawing 5 A. With the glass attached, current climbs to 16 A at mid-travel. What is done?

### Sample 24 · Activity G

**After a door glass replacement, the power window slows and stalls mid-travel. With the glass unbolted, the regulator runs full travel drawing 5 A. With the glass attached, current climbs to 16 A at mid-travel. What is done?**

1. Replace the window regulator
2. Replace the window motor
3. Replace the window switch
4. Realign the run channels (correct)

Run alone, the regulator draws a normal 5 A over full travel, so the motor and regulator are sound; the current rise appears only with the glass attached, so the glass is binding in its path. Realign the run channels so the glass runs true, then recheck travel and current. A new motor, regulator or switch would still be fighting the same bind.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5145.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 25: During uncoupling, the fifth-wheel release handle will not pull. The trailer brakes are set, the landing gear is down, and the tractor stopped after pulling ahead slightly. The handle released easily last time. What is done?

### Sample 25 · Activity H

**During uncoupling, the fifth-wheel release handle will not pull. The trailer brakes are set, the landing gear is down, and the tractor stopped after pulling ahead slightly. The handle released easily last time. What is done?**

1. Ease back against the kingpin (correct)
2. Loosen the lock adjustment
3. Grease the jaws, then pull
4. Raise the trailer on its legs

Pulling ahead leaves the jaws loaded against the kingpin, which binds the release. With the trailer brakes set, easing the tractor back takes that load off the jaws so the handle moves normally. Raising the trailer removes vertical load, not the fore-aft load on the jaws, and a lock that released easily last time does not need readjusting.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5144.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 26: With the trailer supply valve pushed in, a coupled trailer's reservoirs stay at 0 kPa and its spring brakes stay applied. The reservoirs start to fill only while the driver holds the brake pedal down. What is the cause?

### Sample 26 · Activity H

**With the trailer supply valve pushed in, a coupled trailer's reservoirs stay at 0 kPa and its spring brakes stay applied. The reservoirs start to fill only while the driver holds the brake pedal down. What is the cause?**

1. Gladhands crossed at coupling (correct)
2. Supply gladhand seal missing
3. Trailer relay valve leaking
4. Tractor protection valve shut

Filling only during a brake application means service-line air is reaching the trailer supply port, and supply air is going to the trailer control port: the gladhands are crossed. A shut tractor protection valve or a missing supply seal would stop the trailer filling even with the pedal down. A leaking relay valve slows charging regardless of the pedal.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5149.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 27: Airflow is weak from every outlet in every mode, and the blower runs at its normal speed on each setting. What is checked first?

### Sample 27 · Activity I

**Airflow is weak from every outlet in every mode, and the blower runs at its normal speed on each setting. What is checked first?**

1. Cab air filter and intake (correct)
2. Blend door position
3. Blower speed resistor
4. Mode door actuator

Weak flow at every outlet in every mode, with normal blower speed, points to a restriction common to all air paths, and the cab air filter and fresh-air intake are upstream of everything. Mode doors only redirect air and the blend door changes temperature, so neither cuts flow at every outlet in every mode. The blower speed is normal, which clears the speed resistor.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5151.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 28: A truck crane's double-acting boom cylinder drifts in hold. With the boom resting on its support and the cylinder fully retracted, pressure is held on the retract port and the extend-port hose is removed. What shows a leaking piston seal?

### Sample 28 · Activity J

**A truck crane's double-acting boom cylinder drifts in hold. With the boom resting on its support and the cylinder fully retracted, pressure is held on the retract port and the extend-port hose is removed. What shows a leaking piston seal?**

1. Steady flow from the open port (correct)
2. No flow from the open port
3. Pressure rising to relief
4. Oil weeping at the rod wiper

With the piston bottomed and held by retract-side pressure, oil getting past the piston seal can only leave through the open extend port, so steady flow there means the seal leaks. Pressure rising to relief is normal with the cylinder bottomed, and oil at the wiper is the rod seal, an external leak. No flow means the piston seal holds and the drift is likely in the valve.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5152.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 29: A hydraulic pump whines and the reservoir oil is foamy. The level is correct, and vacuum at the pump inlet is 8 kPa at full speed against a 17 kPa maximum. What is the cause?

### Sample 29 · Activity J

**A hydraulic pump whines and the reservoir oil is foamy. The level is correct, and vacuum at the pump inlet is 8 kPa at full speed against a 17 kPa maximum. What is the cause?**

1. Worn pump gear clearances
2. Clogged suction strainer
3. Air drawn in at suction side (correct)
4. Relief valve set too low

Inlet vacuum well under the 17 kPa limit rules out a restricted inlet, which causes cavitation with high vacuum. Foam with normal vacuum means air is entering on the suction side, for example at a loose suction fitting, a cracked suction hose or the pump shaft seal. A low relief setting or worn gears cost pressure or flow but do not aerate the oil.

Skilled Trades Ontario Apprenticeship Training Standard - Truck and Coach Technician (310T), 2016, sub-task 5152.02. https://www.skilledtradesontario.ca/wp-content/uploads/1970/01/Truck-and-Coach-Technician-310T-EN-TS-V100-2016.pdf

### Question 30: A hybrid truck is isolated and the OEM wait time has passed. A suitable voltage-rated meter was proved on a known DC source before testing. It now reads 0 V between HV+ and HV- and from each to chassis. What completes the absence-of-voltage check?

### Sample 30 · Activity K

**A hybrid truck is isolated and the OEM wait time has passed. A suitable voltage-rated meter was proved on a known DC source before testing. It now reads 0 V between HV+ and HV- and from each to chassis. What completes the absence-of-voltage check?**

1. Remove service disconnect
2. Check only HV+ to chassis
3. Switch meter to resistance
4. Prove meter on source again (correct)

Prove the meter again on the known live source to complete the live-dead-live check. Voltage inputs are generally protected differently than current inputs, so a blown current-input fuse alone does not establish that a zero voltage reading is false. If the voltage input or test leads are faulty, the before-and-after checks reveal that failure.

Red Seal Occupational Standard - Truck and Transport Mechanic, task K-40.01, Services hybrid vehicles. This newer RSOS identifies high-voltage hazards but its overview says exams based on it are under development; it is used here only for the four hybrid/EV editorial questions. https://red-seal.ca/_conf/assets/custom/docms/truck-transp-mech/rsos-eng.pdf Also: Fluke, How to Verify Electrical Test Tool Operation with a Proving Unit, proving a tester before and after absence-of-voltage testing. https://www.fluke.com/en-us/learn/blog/digital-multimeters/how-to-verify-electrical-test-tool-operation

## Before you buy

- These questions use the cited occupational standards, curriculum and technical references. Nothing here is reproduced from a real exam.
- Passing this does not guarantee passing the certifying exam, and nothing here is a substitute for the training standard or your in-school hours.
- It is a PDF. There is no login, no expiry and no subscription, and you can print it.
- Automated structure and distribution checks are complete. Technical accuracy review by a licensed tradesperson remains outstanding.

Questions about your purchase or a missing PDF? [Contact Blue Crane Works](mailto:info@bluecraneworks.ca) with the email used at checkout. The download link lasts 30 days; your saved PDF does not expire.

## When you are ready for the real exam

You book the 310T certifying exam yourself in the Skilled Trades Ontario Portal ($150 plus HST) and write it at one of 24 exam centres, or at your college in your final level of school. [How to book it and find the nearest centre](https://tradecredentialregistry.com/canada/ontario/book-your-exam/).

## Writing in Alberta, BC or Manitoba? Same Red Seal exam

The Truck and Coach Technician exam is the national Red Seal exam, so this practice exam fits writers in other provinces too, wherever the trade carries the Red Seal. Trade names differ by province.

- [Alberta Red Seal Practice Exams](https://tradecredentialregistry.com/practice-exams/alberta/)
- [BC Red Seal Practice Exams](https://tradecredentialregistry.com/practice-exams/british-columbia/)
- [Manitoba Red Seal Practice Exams](https://tradecredentialregistry.com/practice-exams/manitoba/)

## Where the exam facts on this page come from

The still-published Red Seal exam-information page lists a 135-question Truck and Transport Mechanic exam and blocks A-K. Its counts are scaled to 150 with largest-remainder rounding. The Red Seal overview says exams based on the newer RSOS are under development, so established-system questions cite the Ontario 310T Apprenticeship Training Standard (2016); only four hybrid/EV questions use the newer RSOS. This is an independent study allocation, not an official examination. The regulation and issuing authority explain the actual credential and examination requirements.

- [Red Seal exam information](https://red-seal.ca/eng/trades/trucktranspmech/exam-information.shtml)
- [O. Reg. 876/21, prescribed trades](https://www.ontario.ca/laws/regulation/210876)
- [Skilled Trades Ontario examination information](https://www.skilledtradesontario.ca/)

## The free reference material for this trade

Everything about the certification itself, the classification, the hours, the ratio and the official sources, stays free on this site and always will. The practice exam is the only thing here that costs anything.

- [Truck and Coach Technician (310T): the full certification record](https://tradecredentialregistry.com/canada/ontario/310t-truck-and-coach-technician/)
- [Which Ontario trades are compulsory, and what that means for you](https://tradecredentialregistry.com/canada/ontario/compulsory-trades/)
- [Which Ontario safety tickets actually expire](https://tradecredentialregistry.com/canada/ontario/safety-training/)
- [Construction Electrician (309A) Practice Exam: 150 questions](https://tradecredentialregistry.com/practice-exams/309a-electrician-construction-and-maintenance/)
- [Gas Technician 2 (G.2) Practice Exam: 150 questions](https://tradecredentialregistry.com/practice-exams/g2-gas-technician/)
- [Plumber (306A) Practice Exam: 150 questions](https://tradecredentialregistry.com/practice-exams/306a-plumber/)
- [Industrial Mechanic Millwright (433A) Practice Exam: 150 questions](https://tradecredentialregistry.com/practice-exams/433a-industrial-mechanic-millwright/)
- [Ontario workplace fatalities and critical injuries by sector](https://tradecredentialregistry.com/canada/ontario/workplace-safety/)
- [Automotive Service Technician (310S): the certification record](https://tradecredentialregistry.com/canada/ontario/310s-automotive-service-technician/)
- [Alignment and Brakes Technician (310E): the certification record](https://tradecredentialregistry.com/canada/ontario/310e-alignment-and-brakes-technician/)
- [Automotive Electronic Accessory Technician (310K): the certification record](https://tradecredentialregistry.com/canada/ontario/310k-automotive-electronic-accessory-technician/)
- [Every practice exam we publish](https://tradecredentialregistry.com/practice-exams/)

## Other practice exams

- [![](https://tradecredentialregistry.com/exam-covers/309a-electrician-construction-and-maintenance-384.png)309A Construction Electrician](https://tradecredentialregistry.com/practice-exams/309a-electrician-construction-and-maintenance/)
- [![](https://tradecredentialregistry.com/exam-covers/g2-gas-technician-384.png)G.2 Gas Technician 2](https://tradecredentialregistry.com/practice-exams/g2-gas-technician/)
- [![](https://tradecredentialregistry.com/exam-covers/306a-plumber-384.png)306A Plumber](https://tradecredentialregistry.com/practice-exams/306a-plumber/)
- [![](https://tradecredentialregistry.com/exam-covers/433a-industrial-mechanic-millwright-384.png)433A Industrial Mechanic Millwright](https://tradecredentialregistry.com/practice-exams/433a-industrial-mechanic-millwright/)
- [![](https://tradecredentialregistry.com/exam-covers/310s-automotive-service-technician-384.png)310S Automotive Service Technician](https://tradecredentialregistry.com/practice-exams/310s-automotive-service-technician/)
- [![](https://tradecredentialregistry.com/exam-covers/g3-gas-technician-384.png)G.3 Gas Technician 3](https://tradecredentialregistry.com/practice-exams/g3-gas-technician/)
- [![](https://tradecredentialregistry.com/exam-covers/332a-hairstylist-384.png)332A Hairstylist](https://tradecredentialregistry.com/practice-exams/332a-hairstylist/)
- [![](https://tradecredentialregistry.com/exam-covers/442a-industrial-electrician-384.png)442A Industrial Electrician](https://tradecredentialregistry.com/practice-exams/442a-industrial-electrician/)
- [![](https://tradecredentialregistry.com/exam-covers/308a-sheet-metal-worker-384.png)308A Sheet Metal Worker](https://tradecredentialregistry.com/practice-exams/308a-sheet-metal-worker/)
- [![](https://tradecredentialregistry.com/exam-covers/415a-cook-384.png)415A Cook](https://tradecredentialregistry.com/practice-exams/415a-cook/)
- [![](https://tradecredentialregistry.com/exam-covers/456a-welder-384.png)456A Welder](https://tradecredentialregistry.com/practice-exams/456a-welder/)
- [![](https://tradecredentialregistry.com/exam-covers/429a-general-machinist-384.png)429A General Machinist](https://tradecredentialregistry.com/practice-exams/429a-general-machinist/)
- [![](https://tradecredentialregistry.com/exam-covers/339a-hoisting-engineer-mobile-crane-operator-1-384.png)339A Mobile Crane Operator](https://tradecredentialregistry.com/practice-exams/339a-hoisting-engineer-mobile-crane-operator-1/)
- [![](https://tradecredentialregistry.com/exam-covers/339b-hoisting-engineer-tower-crane-operator-384.png)339B Tower Crane Operator](https://tradecredentialregistry.com/practice-exams/339b-hoisting-engineer-tower-crane-operator/)

![Truck and Coach Technician (310T) Practice Exam cover](https://tradecredentialregistry.com/exam-covers/310t-truck-and-coach-technician-384.png)**$67.49**150 questions

Get the PDF

---

Source: https://tradecredentialregistry.com/practice-exams/310t-truck-and-coach-technician/
