United States · Official-source record
Plumber license requirements in North Carolina
North Carolina issues plumber licenses at the state level, through The State Board of Examiners of Plumbing, Heating and Fire Sprinkler Contractors.
View sourceWhat the source says
An individual may not perform any work which is within the scope of G.S. 87-21(a)(1), 87-21(a)(2), 87-21(a)(3), 87-21(a)(4), 87-21(a)(11), or 87-21(b)(2), and not otherwise excluded by G.S. 87-21(c), 87-21(c1) or 87-25, for any other individual, firm, body corporate or body politic no matter the form or arrangement of compensation unless such person has been issued the appropriate license by the Board.
What the source says
The mailing address of The State Board of Examiners of Plumbing, Heating and Fire Sprinkler Contractors is 1109 Dresser Court, Raleigh, NC 27609.
Who regulates it
- Regulator
- The State Board of Examiners of Plumbing, Heating and Fire Sprinkler ContractorsView source
What the source says
The mailing address of The State Board of Examiners of Plumbing, Heating and Fire Sprinkler Contractors is 1109 Dresser Court, Raleigh, NC 27609.
- Regulator website
- http://www.nclicensing.orgView source
What the source says
Forms may be obtained on request from the State Board of Examiners of Plumbing, Heating and Fire Sprinkler Contractors, 1109 Dresser Court, Raleigh, North Carolina, 27609, or via document download from the Board's official website at http://www.nclicensing.org.
- Statute or rule
- General Statutes Chapter 87, Article 2; 21 North Carolina Administrative Code, Chapter 50View source
What the source says
To enforce the statutory requirements of General Statutes Chapter 87, Article 2 (Board Laws) and 21 North Carolina Administrative Code, Chapter 50 (Board Rules).
Credential status
- Licensing level
- StateView source
What the source says
An individual may not perform any work which is within the scope of G.S. 87-21(a)(1), 87-21(a)(2), 87-21(a)(3), 87-21(a)(4), 87-21(a)(11), or 87-21(b)(2), and not otherwise excluded by G.S. 87-21(c), 87-21(c1) or 87-25, for any other individual, firm, body corporate or body politic no matter the form or arrangement of compensation unless such person has been issued the appropriate license by the Board.
Credential levels
Plumbing Technician, Class IIView sourceWhat the source says
Plumbing Technician, Class II
What the source says
Plumbing Technician, Class II
- Experience
- 2,500 hoursView source
What the source says
Applicants for a license as a plumbing or heating Class II technician shall present evidence adequate to establish 2500 hours of full-time experience in the installation, maintenance, service, or repair of plumbing or heating systems related to the category for which a technician license is sought, whether or not a license was required for the work performed.
- Exam required
- YesView source
What the source says
Applicants for licensure as a Plumbing, Heating, or Fuel Piping Technician shall obtain a license based on experience, as set forth in Rule .0306 of this Section, and shall pass the Class I or the Class II technical and Board laws and rules parts of the Board-administered examination related to the category for which a technician license is sought.
- Exam provider
- PSI Services LLCView source
What the source says
The North Carolina State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors has contracted with PSI to conduct its examination program.
- Passing mark (%)
- 70View source
What the source says
Examinations provided by the Board are based upon a maximum obtainable grade of 100 points, and a grade of 70 is required to pass.
- Open book
- YesView source
What the source says
The reference material list published by the Board contains a specific listing of all of the publications needed for each examination type; only the books in the category of license you have been approved to take will be allowed to be used during the exam.
- Application fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- Exam fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- License fee
- $75 USDView source
What the source says
The annual license fee for Plumbing, Heating or Fuel Piping Technician licensees listed under a licensed Plumbing, Heating or Fuel Piping Contractor is seventy-five dollars ($75.00).
- Renewal term (years)
- 1View source
What the source says
All licenses expire on the last day of December in each year following their issuance or renewal.
- Continuing education
- Not requiredView source
What the source says
Mandatory Continuing Education was eliminated by the Board in 2012, and is no longer required in order to renew licenses annually; however, the Board does encourage all licensees to continue to attend educational courses appropriate for their qualifications in order to remain current on codes, practices, technologies, and other subjects pertaining to the professional trades.
- Alternate route 1
- Up to one-half of the experience may be in academic or technical training related to the field of endeavor for which the examination is requested.View source
What the source says
Up to one-half of the experience may be in academic or technical training related to the field of endeavor for which the examination is requested.
- Alternate route 2
- A contractor license from this Board exempts the holder seeking an equivalent technician license from examination.View source
What the source says
If you hold a contractor’s license with this Board and are seeking the equivalent technician license you are exempt from examination.
- Alternate route 3
- Current and former military personnel or spouses may receive credit for experience gained during active service.View source
What the source says
Current and former military personnel or spouses may receive credit for experience gained during active service.
Exam parts
Class II technicalView sourceWhat the source says
Class II technical
What the source says
Class II technical
Board laws and rulesView sourceWhat the source says
Board laws and rules parts
What the source says
Board laws and rules parts
Not stated in the official sources we checked: Classroom training, Exam questions, Exam time (minutes), Minimum age, Prerequisite license, Insurance required, Bond required, Person of record required, Class II technical: questions, Class II technical: time (minutes), Class II technical: passing mark (%), Class II technical: exam fee, Board laws and rules: questions, Board laws and rules: time (minutes), Board laws and rules: passing mark (%), Board laws and rules: exam fee.
Plumbing Technician, Class IView sourceWhat the source says
Plumbing Technician, Class I
What the source says
Plumbing Technician, Class I
- Experience
- 3,000 hoursView source
What the source says
Applicants for Licensure as a plumbing or heating Class I technician shall present evidence adequate to establish 3000 hours of full-time experience in the installation, maintenance, service, or repair of plumbing or heating systems related to the category for which a technician license is sought, whether or not a license was required for the work performed.
- Exam required
- YesView source
What the source says
Applicants for licensure as a Plumbing, Heating, or Fuel Piping Technician shall obtain a license based on experience, as set forth in Rule .0306 of this Section, and shall pass the Class I or the Class II technical and Board laws and rules parts of the Board-administered examination related to the category for which a technician license is sought.
- Exam provider
- PSI Services LLCView source
What the source says
The North Carolina State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors has contracted with PSI to conduct its examination program.
- Passing mark (%)
- 70View source
What the source says
Examinations provided by the Board are based upon a maximum obtainable grade of 100 points, and a grade of 70 is required to pass.
- Open book
- YesView source
What the source says
The reference material list published by the Board contains a specific listing of all of the publications needed for each examination type; only the books in the category of license you have been approved to take will be allowed to be used during the exam.
- Application fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- Exam fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- License fee
- $75 USDView source
What the source says
The annual license fee for Plumbing, Heating or Fuel Piping Technician licensees listed under a licensed Plumbing, Heating or Fuel Piping Contractor is seventy-five dollars ($75.00).
- Renewal term (years)
- 1View source
What the source says
All licenses expire on the last day of December in each year following their issuance or renewal.
- Continuing education
- Not requiredView source
What the source says
Mandatory Continuing Education was eliminated by the Board in 2012, and is no longer required in order to renew licenses annually; however, the Board does encourage all licensees to continue to attend educational courses appropriate for their qualifications in order to remain current on codes, practices, technologies, and other subjects pertaining to the professional trades.
- Alternate route 1
- Up to one-half of the experience may be in academic or technical training related to the field of endeavor for which the examination is requested.View source
What the source says
Up to one-half of the experience may be in academic or technical training related to the field of endeavor for which the examination is requested.
- Alternate route 2
- A contractor license from this Board exempts the holder seeking an equivalent technician license from examination.View source
What the source says
If you hold a contractor’s license with this Board and are seeking the equivalent technician license you are exempt from examination.
- Alternate route 3
- Current and former military personnel or spouses may receive credit for experience gained during active service.View source
What the source says
Current and former military personnel or spouses may receive credit for experience gained during active service.
Exam parts
Class I technicalView sourceWhat the source says
Class I technical
What the source says
Class I technical
Board laws and rulesView sourceWhat the source says
Board laws and rules parts
What the source says
Board laws and rules parts
Not stated in the official sources we checked: Classroom training, Exam questions, Exam time (minutes), Minimum age, Prerequisite license, Insurance required, Bond required, Person of record required, Class I technical: questions, Class I technical: time (minutes), Class I technical: passing mark (%), Class I technical: exam fee, Board laws and rules: questions, Board laws and rules: time (minutes), Board laws and rules: passing mark (%), Board laws and rules: exam fee.
State and local government Plumbing TechnicianView sourceWhat the source says
State and local government Plumbing Technician
What the source says
State and local government Plumbing Technician
- Experience
- 3,000 hoursView source
What the source says
Applicants for a license as a State & Local Government Plumbing or Heating Technician shall present evidence to establish 3000 hours of full-time experience in the installation, maintenance, service, or repair of plumbing or heating systems related to the category for which a technician license is sought, whether or not a license was required for the work performed.
- Exam required
- YesView source
What the source says
Applicants for a license as a State & Local Government Plumbing or Heating Technician shall obtain a license based on experience set forth in Paragraph (c) of this Rule and shall pass the Class I technical and Board laws and rules part of the Board-administered examination described in Rule .0301 of this Section related to the category for which a technician license is sought. The applicant need not pass the business part of the examination.
- Exam provider
- PSI Services LLCView source
What the source says
The North Carolina State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors has contracted with PSI to conduct its examination program.
- Passing mark (%)
- 70View source
What the source says
Examinations provided by the Board are based upon a maximum obtainable grade of 100 points, and a grade of 70 is required to pass.
- Open book
- YesView source
What the source says
The reference material list published by the Board contains a specific listing of all of the publications needed for each examination type; only the books in the category of license you have been approved to take will be allowed to be used during the exam.
- Application fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- Exam fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- License fee
- 150 annually, or 75 for a second or subsequent Plumbing or Heating Technician at the same agency location USDView source
What the source says
(i) The annual license fee for a State and local government Technician license is one hundred fifty dollars ($150.00), except as provided in Paragraph (j) of this Rule. (j) The annual license fee for a State and local government Plumbing or Heating Technician license that is listed as the second or subsequent licensee at the same agency location is seventy-five dollars ($75.00).
- Renewal term (years)
- 1View source
What the source says
All licenses expire on the last day of December in each year following their issuance or renewal.
- Continuing education
- Not requiredView source
What the source says
Mandatory Continuing Education was eliminated by the Board in 2012, and is no longer required in order to renew licenses annually; however, the Board does encourage all licensees to continue to attend educational courses appropriate for their qualifications in order to remain current on codes, practices, technologies, and other subjects pertaining to the professional trades.
- Alternate route 1
- An active plumbing or heating contractor license may qualify for the corresponding State and local government technician license without examination.View source
What the source says
Applicants for a license as a State & Local Government Technician who currently hold an active plumbing or heating contractor license issued by this Board may qualify for the corresponding State and local government technician license without examination.
- Alternate route 2
- An active plumbing or heating technician license obtained by examination may qualify for the corresponding State and local government technician license without examination.View source
What the source says
Applicants for a license as a State & local Government Technician who currently hold an active plumbing or heating technician license obtained by examination and issued by the Board may qualify for the corresponding State & Local Government technician license without examination.
Exam parts
Class I technicalView sourceWhat the source says
Class I technical
What the source says
Class I technical
Board laws and rulesView sourceWhat the source says
Board laws and rules parts
What the source says
Board laws and rules parts
Not stated in the official sources we checked: Classroom training, Exam questions, Exam time (minutes), Minimum age, Prerequisite license, Insurance required, Bond required, Person of record required, Class I technical: questions, Class I technical: time (minutes), Class I technical: passing mark (%), Class I technical: exam fee, Board laws and rules: questions, Board laws and rules: time (minutes), Board laws and rules: passing mark (%), Board laws and rules: exam fee.
Private Educational Institution Plumbing TechnicianView sourceWhat the source says
Private Educational Institution Plumbing Technician
What the source says
Private Educational Institution Plumbing Technician
- Experience
- 3,000 hoursView source
What the source says
Applicants for a license as a Private Educational Institution Plumbing or Heating Technician shall present evidence to establish 3000 hours of experience in the installation, maintenance service or repair of plumbing or heating system related to the category for which a technician license is sought, whether or not a license was required for the work performed.
- Exam required
- YesView source
What the source says
shall pass the Class I technical and Board laws and rules part
- Exam provider
- PSI Services LLCView source
What the source says
The North Carolina State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors has contracted with PSI to conduct its examination program.
- Passing mark (%)
- 70View source
What the source says
Examinations provided by the Board are based upon a maximum obtainable grade of 100 points, and a grade of 70 is required to pass.
- Open book
- YesView source
What the source says
The reference material list published by the Board contains a specific listing of all of the publications needed for each examination type; only the books in the category of license you have been approved to take will be allowed to be used during the exam.
- Application fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- Exam fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- License fee
- 150 annually, or 75 for a second or subsequent Plumbing or Heating Technician at the same agency location USDView source
What the source says
(i) The annual license fee for a Private Educational Institution Technician license is one hundred fifty dollars ($150.00), except as provided in Paragraph (j) of this Rule. (j) The annual license fee for a Private Educational Institution Technician license that is listed as the second or subsequent licensee at the same agency location is seventy-five dollars ($75.00).
- Renewal term (years)
- 1View source
What the source says
All licenses expire on the last day of December in each year following their issuance or renewal.
- Continuing education
- Not requiredView source
What the source says
Mandatory Continuing Education was eliminated by the Board in 2012, and is no longer required in order to renew licenses annually; however, the Board does encourage all licensees to continue to attend educational courses appropriate for their qualifications in order to remain current on codes, practices, technologies, and other subjects pertaining to the professional trades.
- Alternate route 1
- An active Class I plumbing or heating contractor license may qualify for the corresponding Private Educational Institution technician license without examination.View source
What the source says
However, applicants for a license as a Private Educational Technician who currently hold an active Class I plumbing or heating contractor license issued by this Board may qualify for the corresponding Private Educational Institution technician license without examination.
- Alternate route 2
- An active plumbing or heating technician license obtained by examination may qualify for the corresponding Private Educational Institution technician license without examination.View source
What the source says
Applicants for a license as Private Educational Institution Technician who currently hold an active plumbing or heating technician license obtained by examination and issued by the Board qualify for the Corresponding Private Educational Institution technician license without examination.
Exam parts
Class I technicalView sourceWhat the source says
Class I technical
What the source says
Class I technical
Board laws and rulesView sourceWhat the source says
Board laws and rules parts
What the source says
Board laws and rules parts
Not stated in the official sources we checked: Classroom training, Exam questions, Exam time (minutes), Minimum age, Prerequisite license, Insurance required, Bond required, Person of record required, Class I technical: questions, Class I technical: time (minutes), Class I technical: passing mark (%), Class I technical: exam fee, Board laws and rules: questions, Board laws and rules: time (minutes), Board laws and rules: passing mark (%), Board laws and rules: exam fee.
Restricted Limited Plumbing ContractorView sourceWhat the source says
Restricted Limited Plumbing Contractor
What the source says
Restricted Limited Plumbing Contractor
- Experience
- 1,500 hoursView source
What the source says
Applicants for a Restricted Limited Plumbing Contractor license shall present evidence at the time of application to establish 1500 hours of full-time experience in the installation, maintenance, service, or repair of plumbing systems, whether or not a license was required for the work performed.
- Exam required
- YesView source
What the source says
shall be required to pass both the business and law part and the technical part of the Restricted Limited Plumbing Contractor examination.
- Exam provider
- PSI Services LLCView source
What the source says
The North Carolina State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors has contracted with PSI to conduct its examination program.
- Passing mark (%)
- 70View source
What the source says
Examinations provided by the Board are based upon a maximum obtainable grade of 100 points, and a grade of 70 is required to pass.
- Open book
- YesView source
What the source says
The reference material list published by the Board contains a specific listing of all of the publications needed for each examination type; only the books in the category of license you have been approved to take will be allowed to be used during the exam.
- Application fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- Exam fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- License fee
- $150 USDView source
What the source says
The annual license fee for a Restricted Limited Plumbing Contractor is one hundred fifty dollars ($150.00).
- Renewal term (years)
- 1View source
What the source says
All licenses expire on the last day of December in each year following their issuance or renewal.
- Continuing education
- Not requiredView source
What the source says
Mandatory Continuing Education was eliminated by the Board in 2012, and is no longer required in order to renew licenses annually; however, the Board does encourage all licensees to continue to attend educational courses appropriate for their qualifications in order to remain current on codes, practices, technologies, and other subjects pertaining to the professional trades.
- Alternate route 1
- Up to one-half of the experience may be in academic or technical training related to the field of endeavor for which the examination is requested.View source
What the source says
Up to one-half of the experience may be in academic or technical training related to the field of endeavor for which the examination is requested.
- Alternate route 2
- An active North Carolina Irrigation Contractor Licensing Board license plus Backflow Inspector certification from a North Carolina municipality or 500 hours of plumbing-system component maintenance, service, or repair permits the applicant to take the examination.View source
What the source says
In lieu of the requirements of Paragraph (j) of this Rule, applicants for a Restricted Limited Plumbing Contractor License who present a current active License from the North Carolina Irrigation Contractor Licensing Board may take the examination, provided the applicant demonstrates that he or she holds certification as a Backflow Inspector from one of the municipalities in North Carolina, or demonstrates 500 hours of experience in the maintenance, service, or repair of components of plumbing systems.
- Alternate route 3
- An active North Carolina On-site Wastewater Contractor certification may permit the applicant to take the restricted limited plumbing examinationView source
What the source says
applicants for a Restricted Limited Plumbing Contractor License who present a current active certification as an On-site Wastewater Contractor, issued by the North Carolina On-Site Wastewater Contractors and Inspectors Certification Board, may take the examination
- Alternate route 4
- Minimum of 8 semester hours of education in a plumbing program through a North Carolina Community College programView source
What the source says
minimum of 8 semester hours of education in a plumbing program through a North Carolina Community College program
- Alternate route 5
- 500 hours of experience in maintenance, service, or repair of plumbing system componentsView source
What the source says
500 hours of experience in the maintenance, service, or repair of components of plumbing systems
Exam parts
NC Restricted Limited Plumbing - Business and LawView sourceWhat the source says
NC Restricted Limited Plumbing - Business and Law
What the source says
NC Restricted Limited Plumbing - Business and Law
- Time (minutes)
- 90View source
What the source says
Duration: 90 Minutes
NC Restricted Limited Plumbing - TechnicalView sourceWhat the source says
NC Restricted Limited Plumbing - Technical
What the source says
NC Restricted Limited Plumbing - Technical
- Time (minutes)
- 150View source
What the source says
Duration: 150 Minutes
Not stated in the official sources we checked: Classroom training, Exam questions, Exam time (minutes), Minimum age, Prerequisite license, Insurance required, Bond required, Person of record required, NC Restricted Limited Plumbing - Business and Law: questions, NC Restricted Limited Plumbing - Business and Law: passing mark (%), NC Restricted Limited Plumbing - Business and Law: exam fee, NC Restricted Limited Plumbing - Technical: questions, NC Restricted Limited Plumbing - Technical: passing mark (%), NC Restricted Limited Plumbing - Technical: exam fee.
Limited Plumbing Water Heater Replacement ContractorView sourceWhat the source says
Limited Plumbing Water Heater Replacement Contractor
What the source says
Limited Plumbing Water Heater Replacement Contractor
- Classroom training
- 6 hoursView source
What the source says
has attended and completed a 6-hour course approved by the Board that covers North Carolina State Residential Plumbing codes requirements, sizing, and installation techniques that relate to the replacement of existing potable water heaters.
- Exam required
- YesView source
What the source says
Applicants for licensure as a Limited Plumbing Water Heater Replacement Contractor shall obtain a license based on experience set forth in Rule .0306 of this Section and shall be required to pass both the business and law part and the technical part of the Limited Plumbing Water Heater Replacement Contractor examination.
- Exam provider
- PSI Services LLCView source
What the source says
The North Carolina State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors has contracted with PSI to conduct its examination program.
- Passing mark (%)
- 70View source
What the source says
Examinations provided by the Board are based upon a maximum obtainable grade of 100 points, and a grade of 70 is required to pass.
- Open book
- YesView source
What the source says
The reference material list published by the Board contains a specific listing of all of the publications needed for each examination type; only the books in the category of license you have been approved to take will be allowed to be used during the exam.
- Application fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- Exam fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- License fee
- $150 USDView source
What the source says
Except as set out in Paragraphs (b) and (d) of this Rule, the annual license fee for plumbing, heating, and fuel piping contractor licenses issued or renewed by the Board is one hundred fifty dollars ($150.00).
- Renewal term (years)
- 1View source
What the source says
All licenses expire on the last day of December in each year following their issuance or renewal.
- Continuing education
- Not requiredView source
What the source says
Mandatory Continuing Education was eliminated by the Board in 2012, and is no longer required in order to renew licenses annually; however, the Board does encourage all licensees to continue to attend educational courses appropriate for their qualifications in order to remain current on codes, practices, technologies, and other subjects pertaining to the professional trades.
- Prerequisite license
- Heating or fuel piping technician or contractor license held for a minimum of two years, in good standing with the BoardView source
What the source says
Applicants for licensure as a Limited Plumbing Water Heater Replacement Contractor shall present evidence at the time of application to establish that they have held a heating or fuel piping technician or contractor license for a minimum of two years, are in good standing with the Board, and has attended and completed a 6-hour course approved by the Board that covers North Carolina State Residential Plumbing codes requirements, sizing, and installation techniques that relate to the replacement of existing potable water heaters.
Exam parts
business and law partView sourceWhat the source says
business and law part
What the source says
business and law part
technical partView sourceWhat the source says
technical part
What the source says
technical part
Not stated in the official sources we checked: Experience, Exam questions, Exam time (minutes), Minimum age, Insurance required, Bond required, Person of record required, business and law part: questions, business and law part: time (minutes), business and law part: passing mark (%), business and law part: exam fee, technical part: questions, technical part: time (minutes), technical part: passing mark (%), technical part: exam fee.
P-II (Plumbing-Class II) ContractorView sourceWhat the source says
P-II (Plumbing-Class II) Contractor
What the source says
P-II (Plumbing-Class II) Contractor
- Experience
- 4,000 hoursView source
What the source says
Plumbing Contractor (Class I or Class II) 4,000 hours
- Exam required
- YesView source
What the source says
Each person being examined by the Board for a contractor license, other than a Fire Sprinkler Installation or Fire Sprinkler Inspection Contractor license, shall be required to pass both the business and law part and the technical part of the examination required by G.S. 87-21(b).
- Exam provider
- PSI Services LLCView source
What the source says
The North Carolina State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors has contracted with PSI to conduct its examination program.
- Passing mark (%)
- 70View source
What the source says
Examinations provided by the Board are based upon a maximum obtainable grade of 100 points, and a grade of 70 is required to pass.
- Open book
- YesView source
What the source says
The reference material list published by the Board contains a specific listing of all of the publications needed for each examination type; only the books in the category of license you have been approved to take will be allowed to be used during the exam.
- Application fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- Exam fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- License fee
- $150 USDView source
What the source says
Except as set out in Paragraphs (b) and (d) of this Rule, the annual license fee for plumbing, heating, and fuel piping contractor licenses issued or renewed by the Board is one hundred fifty dollars ($150.00).
- Renewal term (years)
- 1View source
What the source says
All licenses expire on the last day of December in each year following their issuance or renewal.
- Continuing education
- Not requiredView source
What the source says
Mandatory Continuing Education was eliminated by the Board in 2012, and is no longer required in order to renew licenses annually; however, the Board does encourage all licensees to continue to attend educational courses appropriate for their qualifications in order to remain current on codes, practices, technologies, and other subjects pertaining to the professional trades.
- Person of record required
- YesView source
What the source says
The Board shall issue a license certificate bearing the license number assigned to the qualifying individual.
- Alternate route 1
- Educational credits may account for up to 50% of the required experience.View source
What the source says
Educational credits may account for up to 50% of the required experience.
- Alternate route 2
- An active Plumbing Technician Class I or Class II license obtained by examination, with the experience required for the contractor class, permits an applicant to pass only the business portion of the contractor examination.View source
What the source says
Applicants who hold an active Plumbing, Heating, or Fuel Piping Technician Class I or Class II license obtained by examination, may obtain the Plumbing, Heating or Fuel Piping Contractor Class I or Class II license in the same category and class by meeting the experience requirement listed in Rule .0306 of this Section for the specific contractor license sought and by passing only the business portion of the examination.
- Alternate route 3
- Current and former military personnel or spouses may receive credit for experience gained during active service.View source
What the source says
Current and former military personnel or spouses may receive credit for experience gained during active service.
- Alternate route 4
- A current licensee may apply for the Class II plumbing exam based on a Board license held for 10 consecutive years in good standing without lapses or disciplinary action.View source
What the source says
I certify that I have held a license for 10 (ten) consecutive years in good standing with the Board without lapses or disciplinary action.
- Alternate route 5
- For a Class II plumbing or heating license, good standing requires continuous active licensure for 10 years, current Board fees, and no disciplinary order with specified sanctions in the preceding 10 years.View source
What the source says
A license has been maintained in good standing for the purposes of G.S. 87-21(b)(3) if the license: (1) has remained continuously active for 10 years as of the date of the application request; (2) is current as to all fees payable to the Board as of the date of the application request, and (3) has not been the subject of a disciplinary order that imposed a sanction that included supervised probation, suspension, revocation or restoration of a revoked license during the 10-year period preceding the date of the application request for a Class II plumbing or heating license.
Exam parts
BUSINESS AND LAWView sourceWhat the source says
BUSINESS AND LAW
What the source says
BUSINESS AND LAW
- Time (minutes)
- 90View source
What the source says
Duration: 90 Minutes
P - IIView sourceWhat the source says
P - II
What the source says
P - II
- Time (minutes)
- 240View source
What the source says
Duration: 240 Minutes
Not stated in the official sources we checked: Classroom training, Exam questions, Exam time (minutes), Minimum age, Prerequisite license, Insurance required, Bond required, BUSINESS AND LAW: questions, BUSINESS AND LAW: passing mark (%), BUSINESS AND LAW: exam fee, P - II: questions, P - II: passing mark (%), P - II: exam fee.
P-I (Plumbing-Class I) ContractorView sourceWhat the source says
P-I (Plumbing-Class I) Contractor
What the source says
P-I (Plumbing-Class I) Contractor
- Experience
- 4,000 hoursView source
What the source says
Plumbing Contractor (Class I or Class II) 4,000 hours
- Exam required
- YesView source
What the source says
Each person being examined by the Board for a contractor license, other than a Fire Sprinkler Installation or Fire Sprinkler Inspection Contractor license, shall be required to pass both the business and law part and the technical part of the examination required by G.S. 87-21(b).
- Exam provider
- PSI Services LLCView source
What the source says
The North Carolina State Board of Examiners of Plumbing, Heating, and Fire Sprinkler Contractors has contracted with PSI to conduct its examination program.
- Passing mark (%)
- 70View source
What the source says
Examinations provided by the Board are based upon a maximum obtainable grade of 100 points, and a grade of 70 is required to pass.
- Open book
- YesView source
What the source says
The reference material list published by the Board contains a specific listing of all of the publications needed for each examination type; only the books in the category of license you have been approved to take will be allowed to be used during the exam.
- Application fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- Exam fee
- $75 USDView source
What the source says
An application for a license by examination requires a fee of one hundred-fifty dollars ($150.00), consisting of an application fee of seventy-five dollars ($75.00) and an examination fee of seventy-five dollars ($75.00), which is nonrefundable.
- License fee
- $150 USDView source
What the source says
Except as set out in Paragraphs (b) and (d) of this Rule, the annual license fee for plumbing, heating, and fuel piping contractor licenses issued or renewed by the Board is one hundred fifty dollars ($150.00).
- Renewal term (years)
- 1View source
What the source says
All licenses expire on the last day of December in each year following their issuance or renewal.
- Continuing education
- Not requiredView source
What the source says
Mandatory Continuing Education was eliminated by the Board in 2012, and is no longer required in order to renew licenses annually; however, the Board does encourage all licensees to continue to attend educational courses appropriate for their qualifications in order to remain current on codes, practices, technologies, and other subjects pertaining to the professional trades.
- Person of record required
- YesView source
What the source says
The Board shall issue a license certificate bearing the license number assigned to the qualifying individual.
- Alternate route 1
- Educational credits may account for up to 50% of the required experience.View source
What the source says
Educational credits may account for up to 50% of the required experience.
- Alternate route 2
- An active Plumbing Technician Class I or Class II license obtained by examination, with the experience required for the contractor class, permits an applicant to pass only the business portion of the contractor examination.View source
What the source says
Applicants who hold an active Plumbing, Heating, or Fuel Piping Technician Class I or Class II license obtained by examination, may obtain the Plumbing, Heating or Fuel Piping Contractor Class I or Class II license in the same category and class by meeting the experience requirement listed in Rule .0306 of this Section for the specific contractor license sought and by passing only the business portion of the examination.
- Alternate route 3
- Current and former military personnel or spouses may receive credit for experience gained during active service.View source
What the source says
Current and former military personnel or spouses may receive credit for experience gained during active service.
Exam parts
BUSINESS AND LAWView sourceWhat the source says
BUSINESS AND LAW
What the source says
BUSINESS AND LAW
- Time (minutes)
- 90View source
What the source says
Duration: 90 Minutes
P - IView sourceWhat the source says
P - I
What the source says
P - I
- Time (minutes)
- 240View source
What the source says
Duration: 240 Minutes
Not stated in the official sources we checked: Classroom training, Exam questions, Exam time (minutes), Minimum age, Prerequisite license, Insurance required, Bond required, BUSINESS AND LAW: questions, BUSINESS AND LAW: passing mark (%), BUSINESS AND LAW: exam fee, P - I: questions, P - I: passing mark (%), P - I: exam fee.
Apprenticeship and code requirements
- Code book
- North Carolina State Building CodeView source
What the source says
B - Plumbing Code, 2018 Edition
- Code edition
- 2018View source
What the source says
B - Plumbing Code, 2018 Edition
Moving with it
- Reciprocity states
- Georgia, South Carolina, Tennessee, Virginia, and West Virginia (neighbor-state license recognition); South Carolina technical-examination waiver for plumbing contractor Class I and Class IIView source
What the source says
Neighbor State Licensing Recognition Act - Individuals who are currently permanent residents of North Carolina and also currently hold licensure in the neighboring states of Georgia, South Carolina, Tennessee, Virginia, or West Virginia may be eligible for equivalent licensure in North Carolina.
Sources
Last checked
- 1. http://reports.oah.state.nc.us/ncac/title%2021%20-%20occupational%20licensing%20boards%20and%20commissions/chapter%2050%20-%20plumbing,%20heating%20and%20fire%20sprinkler%20contractors/chapter%2050%20rules.pdf
- 2. http://www.nclicensing.org
- 3. https://nclicensing.org/
- 4. https://nclicensing.org/wp-content/uploads/2026/04/Book-Reference-List-2025-10-ADA.pdf
- 5. https://test-takers.psiexams.com/api/content/bulletin/130
- 6. https://nclicensing.org/wp-content/uploads/2026/05/21-ncac-50-.1101.pdf
- 7. https://nclicensing.org/license-renewal/
- 8. https://nclicensing.org/education/
- 9. https://nclicensing.org/wp-content/uploads/2026/05/PHFPT-2026-06.pdf
- 10. https://nclicensing.org/applicant-information/
- 11. https://nclicensing.org/wp-content/uploads/2022/07/21-ncac-50-.1102.pdf
- 12. https://test-takers.psiexams.com/ncpl/test/YTLQV7V5
- 13. https://nclicensing.org/wp-content/uploads/2026/05/License-Definitions-Contractor-2026-06.pdf
- 14. https://nclicensing.org/wp-content/uploads/2026/05/PHFP-Exam-App-2026-06.pdf
- 15. https://nclicensing.org/wp-content/uploads/2026/05/Current-Licensee-Class-II-Exam-2026-06.pdf
- 16. https://nclicensing.org/wp-content/uploads/2024/12/21-NCAC-50.pdf
- 17. https://test-takers.psiexams.com/ncpl/test/LA9QHBL8
- 18. https://test-takers.psiexams.com/ncpl/test/LA9QHBLU